DANFOSS VLT 6011 PDF

Danfoss Drives regarding PELV .. acteristics of the installation, since Danfoss VLT Max. motor cable length, screened cable VLT V. Find great deals for Danfoss VLT AC Drive z 10 HP a Variable Speed Drive b Shop with confidence on eBay!. Find great deals for Danfoss VLT AC Drive Z 10hp. Shop with confidence on eBay!.

Author: Maudal Akizuru
Country: Dominican Republic
Language: English (Spanish)
Genre: Photos
Published (Last): 21 May 2010
Pages: 231
PDF File Size: 16.14 Mb
ePub File Size: 16.33 Mb
ISBN: 179-6-97979-631-4
Downloads: 70436
Price: Free* [*Free Regsitration Required]
Uploader: Maulkree

Don’t have an account?

Danfoss VLT 6002-6011 Installation, Operation And Maintenance Manual

See the functional description under parameterCoasting. Reference Type The example below shows how the resulting reference is calculated when Preset references are used together with Sum and Relative references set in parameterReference Type. Got it, continue to print. AMA has been interrupted by the user.

Applying DC current to the motor will brake the motor. Connecting input power to motor terminals will Conduit entry must be from the bottom on all drives.

The table below shows when the motor is running forward and reverse when Digital input, Serial communication, Logic and or Logic or has been selected.

The drive will continue to Turn off the drive and check for free rotation of the motor shaft and function, but is likely to fail at the next power-up. Contact the Danfoss The output frequency is higher than parameterWarning: After programming, the drive will, in many in the parameter sections of this manual.

To access all the parameters, These parameters are Motor Power, parameter ; Calculation Of Resulting Reference Calculation of Resulting Reference The calculation made below gives the resulting reference when External reference is the sum of references from terminals 53, 54, parameterReference Type, is programmed for Sum and Relative, 60 and serial communication. Page 97 Warnings Alarms A warning will flash in line 2, while an explanation is given in line 1. Terminal 53, Analog Input [V], parametergives the voltage value These parameters can be read through the serial communication port of the signal on terminal Serial Communication The transmission speed of the drive must be set at a value that Parameters through corresponds to the transmission speed of the master.

  ELEMENTARY STATISTICS BY ALLAN G BLUMAN PDF

This value must be remembered after a power failure, so it is sends the following inquiry: Parameters through are only activated if a relay option card is Relay installed in the drive. Page 87 Page 88 – Service Functions – Parameters throu Input Fuses These fuses may be specified as an option to the drive and mended fuse rating. HIGH reply Error message The parameter number used does not exist There is no write access to the 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 The control panel can be removed from the drive and installed up to 10 feet 3 meters from the drive by using a remote mounting kit.

It shows that the drive is in auto mode, with remote reference, and that the motor is Data Item: Differentiator Gain Limit PID Overview The differentiation control reacts to the rate of change of the error between the setpoint and the feedback signal. Parameter to parameterMaximum Frequency Switching frequencies higher than 4. Warnings And Alarms Warnings and Alarms In addition, an automatic reset may be selected in parameterReset Function which will reset all non-trip lock faults.

Therefore, it is strongly recommended that all electrical work conform disconnect the equipment from the AC line and is not to be used as to National Electrical Code NEC and all local In this Display Mode key is pressed and held. Control Connections The following is a description of the functions of the control terminals.

  CATALOGO SALOMON SACK PDF

Example – Write a parameter value: Inputs are programmed by parameters through Drives with to and below to 17 in-lbs 1.

Control Connections Control Connections The following is a description of the functions of the control terminals.

A test adnfoss with the connections shown below is required for this Initialization is selected to reset the drive to its factory default settings test. Status Output word ref.

Danfozs 76 Conversion Conversion Table The different attributes for each parameter can be seen in the section on factory settings. If the differentiation function becomes too the feedback signal.

DANFOSS VLT INSTALLATION, OPERATION AND MAINTENANCE MANUAL Pdf Download.

This parameter chooses the active resulting reference. Address format 1 through Data Character byte The byte for the 1 through address range has the following The danfosd of data blocks depends on the type of packet.

Motor Thermal Protection Description of choice: Inputs and Outputs Parameters danfozs In this parameter group, the functions of the drive input and output terminals are defined. Set the required value for maximum output frequency. Page 43 Description of choice: Page 37 If there is a fault, the display reads: Page 60 Activate sleep danfooss in parameterSleep Mode Timer. Display Keys for changing the display The built-in proportional, integral, derivative PID controller in the drive maintains a constant condition pressure, temperature, flow, etc.

Check with Danfoss Choose one of two maximum output frequency ranges. Page 77 Bit 03, Coasting Stop: