View and Download D-Link DSLB user manual online. DSLB Modem pdf manual download. Don’t follow these instructions until you have received confirmation that your broadband service is ready to use. Have you got your broadband username. Section 1 – Product Overview. D-Link DSLB User Manual. 3. Package Contents. • DSLB ADSL Modem. • Power Adapter. • CD-ROM with User Manual.
|Published (Last):||27 July 2011|
|PDF File Size:||4.27 Mb|
|ePub File Size:||14.48 Mb|
|Price:||Free* [*Free Regsitration Required]|
Using a power supply with a different voltage rating than the one included with the DSLB will cause damage and void the warranty for this product. SPI inspects the contents of all incoming packet headers before deciding what packets are allowed to pass through. For Quality of Service QoSthe router supports multiple priority queues to enable a group of home or office users to experience the benefit of smooth network connection of inbound and outbound data without concern of traffic congestion.
This eliminates the need to reconfigure every host whenever changes in network topology occur. This provides Internet access to everyone in the office for the price of a single user. NAT improves network security in effect by hiding the private network behind one global and visible IP address. High Performance – Very high rates of data transfer are possible with the Router.
DSLB ADSL2+ Ethernet Modem | D-Link UK
Up to 24Mbps downstream bit rate using the G. Easy Installation – The DSLB uses a web-based graphical user interface program for convenient management access and easy set up.
Any common web browser software can be used to manage the Router. When the device manua, powered off this remains dark. LAN A solid green light indicates a valid link on startup. These lights blink when there is activity currently passing through the Ethernet port. This will light after the ADSL negotiation process has been settled.
How to setup DSL 320B revision Z1 in bridge mode
Internet Steady green light indicates a successful Internet connection. Steady red light indicates failed Internet connection. Dark manuual no WAN protocol is configured.
Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, ddsl in the attic or garage. Before you Begin Please read and make sure you understand all the prerequisites for proper installation of your new Router. Have all the necessary information and equipment on hand before beginning the installation.
For some users, only their account information Username manial Password is required. For others, various parameters that control and define the Internet connection will be required.
You can print out the two pages below and use the tables to list this information. This way you have a hard copy of all the information needed to setup the Router. If it is necessary to reconfigure the device, all the necessary manuao can be easily accessed.
Be sure to keep this information safe and private. Low Pass Filters Since ADSL and telephone services share the same copper wiring to carry their respective signals, a filtering mechanism may be necessary to avoid mutual interference. A low pass filter device can be installed for each telephone that shares the line with the ADSL line. Ask your service provider for more information about the use of low pass filters with manuall installation.
Likewise, most fully assembled desktop computers come with an Ethernet NIC adapter 230b standard equipment. If your computer does not have an Ethernet port, you must install an Ethernet NIC adapter before you can use the Router. If you must install an adapter, follow the installation instructions that come with the Ethernet NIC adapter.
Additional software must be installed if you are using the device a simple bridge. For a bridged connection, the information needed to make and maintain the Internet connection is stored 320n another computer or gateway device, not in the Router itself.
In this case, it is not necessary to install software on your computer. It may however be necessary to change some settings in the device, including account information used to identify and verify the connection. All connections to the Internet require a unique global IP address. The Manuzl address can be assigned in a number of ways. Your network service provider will give you instructions about any additional connection software or NIC configuration that may be required. This is used to verify the identity of your account.
Most users will use the default settings. Some users may need to change the type of modulation used for their service. This setting can be changed in the WAN Settings window of the web management interface. VCI Most users will not be required to change this setting. When you attempt to connect to the device through manyal web browser you will be prompted to enter this Username. The default Username for the Router is admin.
The user cannot change this. Password This is the Password you will be prompted to enter when you access the Router s management interface.
The default Password is admin. The user may change this. The default subnet mask is This can be changed later.
This means that it can assign an IP address, subnet mask, and a default gateway address to computers on your LAN. It is recommended that your collect and record this information here, or in some other secure place, in case you have to re-configure your ADSL connection in the future.
Carefully consider the Router s location suitable for connectivity for your Ethernet devices. Place the Router in a location where it can be connected to the various devices as well as to a power source. The Router should not be located where it will be exposed to moisture, direct sunlight or excessive heat. Make sure the cables and power cord are placed safely out of the way so they do not create a tripping hazard. As with any electrical appliance, observe common sense safety procedures.
The Router can be placed on a shelf, desktop, or other stable platform. If possible, you should be able to see the LED indicators on the front if you need to view them for troubleshooting.
Power on Router The Router must be used with the power adapter included with the device. Insert the AC Power Adapter cord into the power receptacle located on the rear panel of the Router and plug the adapter into a suitable nearby power source. If this is the first time installing the device, some settings may need to be changed before the Router can establish a connection.
Press and hold the reset button while the device is powered off. Turn on the power. Remember that this will wipe out any settings stored in flash memory including user account information and LAN IP settings. The device settings will be restored to the factory default IP address and the subnet mask isthe default management Username is admin and the default Password is admin. If you are using a low pass filter device, follow the instructions included with the device or given to you by your service provider.
It is the physical link to the service provider s network backbone and ultimately to the Internet. When connecting the Router to any Ethernet device that is capable of operating at speeds higher than 10Mbps, be sure that the device has auto-negotiation NWay enabled for the connecting port.
Use standard twisted-pair cable with RJ connectors. Follow standard Ethernet guidelines when deciding what type of cable to use to make this connection. When connecting the Router directly to a PC or server use a normal straight-through cable. Be sure that the cable connecting the LAN to the Router does not exceed meters.
If you wish to reserve the uplink port on the switch or hub for another device, connect to any on the other MDI-X ports 1x, 2x, etc. Web-based Configuration Utility Connect to the Router To configure the WAN connection used by the Router it is first necessary to communicate with the Router through its management interface, which is HTML-based and can be accessed using a web browser. To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router.
Type admin for the User Name and admin in the Password field. If you get a Page Cannot be Displayed error, please refer to the Troubleshooting section for assistance. The following chapter describes the various windows used to configure and monitor the Router including how to change IP settings and DHCP server setup. Click on the Next button to continue.
Confirm Password must be same as “New Password”. Of course, you can click on the Skip to ignore the step. Of course, you can modify the information. Click on the Next button to go to the next Setup Wizard window.
Type service name which is from your ISP on the Servername option. The default time is 0 and it means it is always on. The default mode is Disabled.
The default mode is disabled. Set Default Route mode to enable or disable default route, in order to access Internet, suggest enable default route. The default mode is enabled.